
Chemical-free mold removal for Bloomington homes and businesses
Dry Ice Blasting Mold Bloomington CA done right the first time
Dry ice blasting mold Bloomington CA is a waterless, chemical-free way to strip black mold off wood studs, brick, and block. We handle dry ice mold remediation Bloomington CA for homeowners and property managers across San Bernardino County. If you found mold after a roof leak, a burst supply line, or a slow drip behind the washer, we can stop it from spreading and get your space back to normal.
What's included
What our dry ice blasting mold service includes
Every dry ice blasting mold job we run in Bloomington includes containment, HEPA filtration, blasting, antimicrobial treatment, and third-party clearance testing. Here is what is covered in a standard scope, and what we quote separately if your job needs it.
Full inspection and written scope
We walk the property with a moisture meter and thermal imaging camera, check wall cavities with a boroscope inspection camera, and give you a written scope with photos. You know exactly what we are blasting and why before we start.
Containment and negative air
We build 6-mil poly containment with zipper doors and run a negative air machine with HEPA filters for the duration of the job. That keeps mold spore contamination from spreading into clean areas of your home or building.
Dry ice blasting of affected surfaces
Technicians in personal protective equipment blast the mold off wood studs, block, brick, and other salvageable substrates. We run a HEPA vacuum alongside to capture debris as it comes off. Most residential areas take two to four hours.
Antimicrobial and encapsulation
After blasting, we apply an antimicrobial coating to the cleaned framing. Where framing is staying in place, we follow with an encapsulation sealant. This is what keeps musty odors from returning once the job is done.
Post-remediation clearance testing
We pull air and surface samples after the work is complete and send them to a third-party lab such as EMSL Analytical or Pro-Lab. You get the raw report in one to three business days. If counts are still elevated, we re-clean at no extra charge.
Service overview
What dry ice blasting mold Bloomington CA actually does
Dry ice blasting mold Bloomington CA is a remediation method that fires soft dry ice pellets at roughly -109°F through a compressed-air nozzle. The pellets hit the mold, freeze it, and lift it off the surface without water, sand, or chemical residue. Because there is no moisture added, wood studs, brick, and block come out clean and dry instead of soaked. We pair the blaster with a HEPA vacuum and air scrubber so loosened spores get captured instead of drifting into the rest of your house.
Bloomington sits in San Bernardino County where summer heat pushes attic temperatures past 140°F and winter rain finds every roof flashing that was never sealed right. That swing feeds black mold growth in attics, crawl spaces, and bathrooms. If you have been searching dry ice mold remediation near me Bloomington California after a water heater leak or a slow roof drip, this is the service that gets the surface clean without tearing out framing you can save. We also handle dry ice blasting mold after water damage Bloomington CA so the rebuild can start on a dry, clean structure.
The service timeline
Our dry ice blasting mold process, step by step
The process flexes to the condition, but these checkpoints keep decisions clear.
Inspection and moisture mapping
We walk the space with a moisture meter and a thermal imaging camera to find where the water actually came from. A boroscope inspection camera goes into wall cavities and behind baseboards. You get a written scope with photos the same day, usually within two to three hours on site.
Containment and air control
We build 6-mil poly containment with zipper doors and seal it with duct tape, then set a negative air machine with HEPA filters so the room stays under negative pressure. That keeps mold spore contamination from spreading into clean areas of your home while we work.
Dry ice blasting
Technicians in personal protective equipment run the dry ice blasting machine at 80 to 150 PSI depending on the substrate. Soft pellets strip mold off wood studs and block, and a HEPA vacuum runs alongside to capture debris. A typical attic or crawl space takes two to four hours.
Antimicrobial and encapsulation
Once the surface is clean and dry, we apply an antimicrobial coating to the framing. Where framing is staying in place, an encapsulation sealant locks down any residual spores. This is the step that keeps musty odors from coming back after the blasting is done.
Clearance testing
We run a spore trap sampler and air sampling media through a third-party lab such as EMSL Analytical or Pro-Lab. You get the lab report in one to three business days. If counts are still elevated, we re-clean at no additional charge before we call the job complete.
Tools & methods
Tools and methods we use on every job
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Dry ice blasting machine
Fires soft dry ice pellets at roughly -109°F to freeze and lift mold off wood, brick, and block without water or abrasive media. We adjust pressure between 80 and 150 PSI depending on the substrate.
Thermal imaging camera
Reveals temperature differences that point to hidden moisture behind walls, under floors, and in ceilings. It is how we find the leak source before we start blasting anything.
Boroscope inspection camera
Lets us see inside wall cavities and block voids without opening them up. We use it to confirm the extent of hidden mold after leaks so the scope matches the actual problem.
HEPA vacuum and air scrubber
Captures airborne spores and debris during and after blasting. We run them continuously inside containment so nothing escapes into clean areas of the building.
Negative air machine
Keeps the containment under negative pressure so air flows in, not out. This is the single most important piece of equipment for keeping mold spore contamination out of the rest of your home.
Moisture meter
Reads moisture content in wood, drywall, and masonry. We use it to find the water source, confirm the structure is dry before blasting, and verify it stays dry afterward.
Spore trap sampler
Collects airborne spores on a cassette for lab analysis. We use it before work starts to establish a baseline and after work is done to prove the job is complete.
Use cases
When to call for dry ice blasting mold
These examples show how the service framework adapts rather than forcing every call through one repair.

Crawl space framing restored in Bryan Park
A Bryan Park home had mold on roughly 40 feet of floor joists and subfloor from years of ground moisture with no vapor barrier. The musty smell was noticeable in the living room every time the HVAC ran. → We installed a vapor barrier, ran dry ice blasting mold cleaning on the joists and subfloor, and applied an encapsulation sealant. The musty odor was gone within a week, and clearance testing confirmed normal spore counts.
Commercial unit back online in four days
A commercial building in Downtown Bloomington had mold in two tenant spaces after a supply line failed over a weekend. Roughly 500 square feet of block wall and framing were affected, and the owner needed the units back online fast. → We scheduled work around tenant hours, set containment in each unit, and ran dry ice blasting mold for commercial buildings on the affected block and framing. Clearance testing passed on the first round, and the rebuild crew started the next day.
Problems we solve
Mold problems we solve for Bloomington properties
Most of the dry ice blasting mold jobs we run in Bloomington start with one of these four problems. Each one has a different fix, and getting the diagnosis right is what keeps you from paying for work you do not need.
Black mold growth on attic sheathing after a roof leak
We inspect the attic with a moisture meter and thermal imaging camera to find the leak source, then set containment and blast the sheathing and rafters clean. A HEPA vacuum and air scrubber run throughout, and we finish with an antimicrobial coating on the cleaned wood.
Crawl space mold from poor drainage and high humidity
We inspect the crawl space, identify the moisture source, and run dry ice blasting mold cleaning Bloomington CA on the joists and subfloor. Because blasting adds no water, the wood stays dry and the job does not need extra drying days afterward.
Hidden mold behind drywall after a slow supply line leak
We use a boroscope inspection camera to confirm what is behind the wall before we open anything. Once we know the extent, we set containment, remove unsalvageable drywall, and blast the framing clean. Clearance testing confirms the air is safe before we close up.
Musty odors that keep coming back after a DIY cleanup
We track the odor to its source with moisture readings and thermal imaging, then remove the mold properly with dry ice blasting and HEPA vacuuming. An antimicrobial coating and encapsulation sealant finish the job so the smell does not come back.
Pricing process
Dry ice blasting mold pricing in Bloomington
$1,200 - $4,500 for most residential jobs; commercial and large-loss work quoted separately
Square footage affected
Blasting time scales with surface area. A 100-square-foot attic section takes about two hours; a 500-square-foot commercial space can take a full day. This is usually the single biggest line item in the quote.
Containment complexity
A single sealed room is straightforward. Multi-room jobs, occupied commercial spaces, and areas with HVAC returns inside the work zone need more containment and more air scrubbing time, which adds labor and equipment hours.
Substrate type
Wood studs and sheathing blast quickly. Block and brick take longer because of surface texture, and heavy buildup may need a second pass. We adjust pressure and media flow to match the substrate without damaging it.
How much does dry ice blasting mold cost in Bloomington CA?
Most residential dry ice blasting mold jobs in Bloomington run $1,200 to $4,500 in 2026, depending on square footage and how much framing is affected. A single attic or crawl space typically lands in the $1,200 to $2,200 range. Commercial buildings and jobs that need extensive containment or reconstruction run higher. We give you a written range after the inspection, before any work starts.
What is dry ice blasting mold removal in Bloomington California?
It is a cleaning method that uses compressed air to fire dry ice pellets at mold-covered surfaces. The pellets are about -109°F, so they freeze the mold and pop it off wood, brick, or block without water or chemicals. The dry ice turns back into gas on contact, so there is nothing to rinse and nothing left behind but clean, dry framing.
Is dry ice blasting safe for mold in Bloomington CA?
Yes, when it is done by trained technicians in proper containment. The blasting itself is safe for wood studs, brick, and most masonry because it does not gouge the surface the way sandblasting can. The main risk is airborne spores during blasting, which is why we run negative air machines with HEPA filtration and wear full personal protective equipment. Occupants stay out of the work zone until clearance testing passes.
Who does dry ice mold remediation near me in Bloomington?
Mold Remediation Service Bloomington handles dry ice mold remediation for homes and businesses across Bloomington and San Bernardino County. We cover ZIP 92316 and the surrounding neighborhoods, and we can be on site the same day for emergencies. Call (833) 929-5837 and we will schedule an inspection, usually within 24 hours.
Ready when you are
Get dry ice blasting mold Bloomington CA scheduled today
Call (833) 929-5837 and we will schedule an inspection, usually within 24 hours. We are licensed, insured, and we work to ANSI/IICRC S520 standards on every job. You get a written scope, third-party clearance testing, and a price that does not change after we start.

Talk with the local team
Request Dry Ice Blasting Mold
Call (833) 929-5837 any time, day or night, and a live person will answer. We schedule free inspections seven days a week and can usually get to your BLOOMINGTON property the same day. If you prefer email, send photos of what you are seeing and we will follow up with next steps.



