Mold Inspection

Certified inspectors, moisture mapping, and lab-backed answers fast

Mold inspection Bloomington CA you can schedule today

A mold inspection Bloomington CA homeowners and landlords call first should tell you three things: where the growth is, how bad it is, and what it will take to fix it. We walk every room with moisture meters and thermal cameras, sample the air, and hand you a written report you can act on. If you have smelled something musty since the last rain, book a mold assessment Bloomington CA before the colony doubles.

Live phone supportUpfront optionsBacked workmanship
Call firstLive triage can help before arrival
Safety before speedRisks assessed before work begins
Diagnose the causeWe trace the source, not just the symptom
Approve the workScope and price explained upfront

What's included

What our mold inspection service includes

Every inspection we run in Bloomington follows the same baseline scope. Lab sample count and square footage are the two variables that change the price, and we tell you both before we schedule.

01

Full visual walkthrough

Exterior grading, roof flashing, attic sheathing, crawl space joists, and every interior room. We photograph anything that reads wet or shows discoloration and note it in the report with a location.

02

Moisture and thermal readings

A calibrated moisture meter and thermal imaging camera read every wall, ceiling, and floor plane. We log the numbers so you can see exactly how wet each area is compared to a dry reference point.

03

Air and surface sampling

Spore trap cassettes collect air in the affected room and outdoors for baseline. Tape lifts or swabs go on visible growth. Samples ship the same day to EMSL Analytical or Pro-Lab for genus-level identification.

04

Written report with photos

You get a PDF with moisture maps, thermal images, lab results, and a remediation scope written to ANSI/IICRC S520. It is formatted so an adjuster, contractor, or buyer can read it without a phone call.

05

Walkthrough and next steps

We go over the findings by phone or in person, answer every question, and lay out your options. If remediation is needed, we quote it separately so you can compare bids without pressure.

Service overview

What a mold inspection Bloomington CA actually covers

A mold inspection Bloomington CA is a non-invasive, room-by-room investigation that locates active mold growth, hidden moisture, and the conditions feeding it. We start outside the house and work inward: foundation grading, crawl space vents, attic sheathing, then every interior wall, cabinet, and ceiling plane. Moisture meters and thermal imaging cameras read what your eyes cannot, and a boroscope inspection camera slips behind baseboards and inside wall cavities without cutting drywall. Air sampling with spore trap cassettes tells us whether spores are elevated compared to outdoor baseline levels.

Bloomington sits in San Bernardino County, where summer attic temperatures push past 130 degrees and winter rain finds every failed roof flashing. That swing creates condensation on cold ductwork, and hidden mold after leaks is the number one reason people call us. If you have spotted black mold growth near a bathroom vent or smelled a musty odor in a back bedroom, a professional mold inspection in Bloomington CA is the cheapest way to find out whether you are looking at a $400 cleanup or a $4,000 one.

Find hidden growth fastA thermal imaging camera and moisture meter read temperature and moisture differences behind drywall, under flooring, and inside ceiling cavities. In a typical 1,800 square foot Bloomington home, the full walkthrough takes 60 to 90 minutes and catches the wet spots that never show a stain.
Lab-backed, not guessworkWe collect air samples with spore trap cassettes and send them to an accredited lab such as EMSL Analytical or Pro-Lab. You get genus-level results in 24 to 48 hours, so you know whether you are dealing with common Cladosporium or something that needs immediate containment.
A written scope you can bidThe report lists affected square footage, moisture readings, photos, and a recommended remediation scope written to ANSI/IICRC S520 language. Contractors and insurance adjusters can price directly off it, which ends the back-and-forth over what actually needs to come out.
Mold Inspection
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.

The service timeline

How our mold inspection process runs

The process flexes to the condition, but these checkpoints keep decisions clear.

01

Phone intake

We ask about the smell, the stains, the last water event, and the age of the house. That conversation takes 10 minutes and lets us load the right gear. If you need a same day mold inspection Bloomington CA, tell us on the call and we will fit you into the next open slot, including evenings.

Stage 1
02

Exterior walk

We check roof flashing, grading, sprinkler placement, and crawl space vents before stepping inside. Most moisture problems in Bloomington start outside and travel in. This pass takes 15 to 20 minutes and often explains the reading we are about to get in the back bedroom.

Stage 2
03

Interior survey

Room by room with a moisture meter and thermal imaging camera. We pull refrigerator and washing machine panels, check under every sink, and read the attic sheathing and crawl space joists. The boroscope inspection camera goes into any wall cavity that reads wet.

Stage 3
04

Air and surface sampling

We run a spore trap sampler in the affected room and one outdoors for baseline comparison. Tape lifts or swabs go on visible growth. Samples ship the same day to the lab, and results come back in 24 to 48 hours with genus identification.

Stage 4
05

Report and walkthrough

You get photos, moisture maps, lab results, and a written scope. We walk you through it by phone or in person, answer questions, and hand off a remediation plan you can bid out. If you want us to do the work, we schedule it on that same call.

Stage 5

Tools & methods

Tools and methods we use on every job

Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.

01

Moisture meter

Reads percent moisture content in drywall, wood framing, and flooring. We log readings against a dry reference so you can see how wet each area actually is.

02

Thermal imaging camera

Detects temperature differences behind walls and ceilings that indicate hidden moisture. It finds wet spots that have not yet stained the surface.

03

Boroscope inspection camera

Slips behind baseboards and inside wall cavities through a small hole. Lets us see mold growth and water damage without cutting open drywall.

04

Spore trap sampler and cassettes

Collects a measured volume of air onto a spore trap cassette. The lab counts spores per cubic meter and identifies genus.

05

Air scrubber and negative air machine

Used during remediation to filter airborne spores and maintain negative pressure inside containment so contamination does not spread to clean rooms.

06

HEPA vacuum

Removes settled spores from surfaces and framing after removal. Standard shop vacuums blow fine particles back into the air, which is why HEPA filtration matters.

07

Dehumidifier and Dri-Eaz drying equipment

Pulls moisture out of wall cavities and subfloor assemblies after a water event. Drying before removal prevents the mold from returning.

Use cases

When to schedule a mold inspection

These examples show how the service framework adapts rather than forcing every call through one repair.

Mold Inspection
Attic mold after a roof valley leakA homeowner in Bryan Park noticed a musty smell in the hallway every time the AC ran. The attic had never been inspected. Our thermal camera found wet sheathing across a 6-foot section, and air samples came back with elevated Penicillium and Aspergillus counts. → We scoped remediation for 120 square feet of affected sheathing and framing. The roof valley was repaired, the affected decking was treated, and post-remediation testing confirmed spore counts had returned to outdoor baseline within 10 days.

Bathroom mold behind the shower wall

A rental unit in Bloomington Central had recurring black spots along the shower caulk line that the tenant kept wiping away. Our boroscope camera found mold growth on the drywall behind the tile, and the moisture meter read 28 percent on the adjacent stud. → We removed 32 square feet of affected drywall, treated the framing with Concrobium, and applied an antimicrobial coating. Clearance samples came back clean, and the shower pan was resealed to stop the leak.

Crawl space mold after a slab leak

A home in Prospect Hill had a slow slab leak for months before anyone noticed. The crawl space joists read 24 percent moisture, and visible mold growth covered roughly 200 square feet of subfloor and framing. → We installed a new vapor barrier, ran dehumidifiers and negative air machines for four days, then removed the affected insulation and treated the framing. Post-remediation mold testing confirmed clearance, and the slab leak was repaired by a licensed plumber.

Problems we solve

Mold problems we solve for Bloomington homes

Most of the calls we get start with a smell, a stain, or a symptom. Here are the four problems we see most often and how a proper inspection resolves each one.

ISSUE

Musty odor with no visible mold

We use a thermal imaging camera and boroscope inspection camera to locate the source without demolition, then confirm it with air sampling. Once we know where it is, the fix is targeted instead of exploratory.

SYMPTOM

Black mold growth near a bathroom or window

We read the wall cavity with a moisture meter, sample the growth to confirm genus, and identify the water source. The report tells you whether the drywall needs to come out or the surface can be treated.

SIGN

Attic or crawl space mold after a leak

We inspect the sheathing, joists, and insulation, log moisture readings across the space, and sample the air. Remediation is scoped to the affected framing, and we correct the ventilation or vapor barrier issue that caused it.

ALERT

Mold spore contamination after water damage

We run air sampling room by room to map where contamination has spread, then scope remediation with containment, HEPA vacuuming, and post-remediation mold testing to confirm clearance.

Pricing process

What a mold inspection costs in Bloomington

$300 - $650 for most residential inspections; commercial quoted per building

Phase 01

Home square footage

A 1,200 square foot home takes about 60 minutes to inspect. A 3,000 square foot home with multiple levels takes closer to two hours and requires more moisture readings and photos in the report.

Phase 02

Number of lab samples

Each air sample with spore trap cassettes runs $75 to $125 depending on the lab and turnaround. Most homes need two to four samples, and rush 24-hour turnaround adds to the per-sample cost.

Phase 03

Attic and crawl space access

Tight crawl spaces and attics with limited access take longer and sometimes require a boroscope inspection camera instead of a full walkthrough. That adds time to the visit and detail to the report.

Questions before we arrive

Frequently Asked Questions

Mold Inspection
Call (833) 929-5837
How much does a mold inspection cost in Bloomington CA?

Most residential inspections in Bloomington run $300 to $650 in 2026, depending on square footage and how many air samples you need. A basic visual inspection with two samples sits at the low end; a full home with attic, crawl space, and four lab samples sits at the high end. Commercial mold inspection Bloomington CA pricing is quoted per building. Call (833) 929-5837 for a flat number before we come out.

What does a mold inspection include in Bloomington California?

It includes a full exterior and interior walkthrough, moisture meter and thermal imaging readings on every wall and ceiling plane, boroscope inspection of suspect cavities, air sampling with spore trap cassettes, and a written report with photos and lab results. You also get a remediation scope written to ANSI/IICRC S520 standards. The visit itself takes 60 to 120 minutes depending on home size.

How often should I get a mold assessment in Bloomington CA?

Once a year is right for most homes, and always within 48 hours of any water event. Bloomington's summer heat and winter rain cycles mean attic and crawl space moisture builds quietly. If you have had a roof leak, slab leak, or AC condensate overflow, book a mold inspection and assessment Bloomington California right away rather than waiting for the annual slot.

Who does mold inspection in Bloomington CA near me?

We do. Mold Remediation Service Bloomington has been inspecting homes and commercial buildings in Bloomington and across San Bernardino County since 2023. Our inspectors hold IICRC WRT, ASD, and AMRT credentials and use calibrated moisture meters, thermal cameras, and accredited labs. We cover ZIP 92316 and the surrounding area, with same-day slots available most weekdays.

Ready when you are

Book your mold inspection Bloomington CA today

Same-day and 24/7 appointments are available across Bloomington and San Bernardino County. Call (833) 929-5837 and we will get an inspector to your door, collect samples, and have lab results back to you within 48 hours.

Mold Inspection

Talk with the local team

Request Mold Inspection

Call (833) 929-5837 any time, day or night, and a live person will answer. We schedule free inspections seven days a week and can usually get to your BLOOMINGTON property the same day. If you prefer email, send photos of what you are seeing and we will follow up with next steps.

18762 Valley Blvd, Bloomington, CA 92316, USA, BLOOMINGTON, CaliforniaMain office · technicians serve the full area

Thanks — your request is in. We will contact you shortly.

Call now