
Certified containment, removal, and clearance testing in San Bernardino County
Mold abatement Bloomington CA done right the first time
When mold shows up in your Bloomington home, you want it gone, not painted over. Our mold abatement Bloomington CA crews contain the work area, pull the growth, and verify the air is clean before we pack up. We handle attic, crawl space, and post-leak mold across San Bernardino County, with same-day inspections and honest pricing from the first call.
What's included
What our mold abatement service includes
Every mold abatement job we run in Bloomington includes the same core scope: inspection, containment, removal, treatment, drying, and clearance testing. Rebuild and source repair are quoted separately so you can see exactly what you are paying for. Here is what is covered.
On-site inspection and moisture mapping
A certified technician maps every wet zone with a moisture meter and thermal imaging camera, photographs visible growth, and identifies the moisture source. You get a written scope and fixed price the same day, before any work starts.
Containment and negative air
We build critical barriers with 6-mil poly and zipper doors, then run a negative air machine with HEPA filtration for the duration of the job. This keeps spores from spreading into clean rooms, which is the single biggest cost driver on any abatement.
Removal of contaminated materials
Porous materials that cannot be cleaned, like drywall, insulation, and carpet, come out in sealed bags and get disposed of per California Department of Public Health guidelines. Structural wood stays and gets cleaned, not replaced, whenever the standard allows.
HEPA vacuuming and antimicrobial treatment
Framing, block walls, and subfloor get HEPA vacuumed, wire brushed where needed, and treated with an antimicrobial coating. Cavities get fogged with Benefect or Concrobium. Where the substrate allows, we use dry ice blasting for a cleaner finish.
Drying to dry standard
Dehumidifiers and air movers run until moisture readings match dry standard for the material type. This usually takes 24 to 72 hours. We log readings daily so you can see the structure actually drying, not just sitting.
Clearance testing and written report
Post-remediation verification with a spore trap sampler and air sampling media confirms indoor spore counts are at or below outdoor baseline. You get the lab report from EMSL Analytical or Pro-Lab in writing, plus photos of the finished work.
Service overview
What mold abatement Bloomington CA actually involves
Mold abatement Bloomington CA is the physical removal of mold growth, contaminated materials, and settled spores from a building, followed by cleaning and verification that the contamination is gone. It is not a spray-and-wipe job. We set up containment with 6-mil poly and zipper doors, run a negative air machine with HEPA filtration, and remove porous materials like drywall and insulation that cannot be saved. Structural wood gets HEPA vacuuming, wire brushing, and an antimicrobial coating before any rebuild starts.
In Bloomington, most of our calls come from three places: swamp coolers that drip into attic decking, slab leaks that wick up into baseboards, and bathroom exhaust fans that vent into the attic instead of outside. Summer heat pushes attic temps past 130 degrees, which speeds mold growth after any moisture event. If you are searching for mold mitigation near me Bloomington California because of a recent leak, the clock matters. Mold can colonize wet drywall in 24 to 48 hours, so same-day inspection saves you money.
The service timeline
How our mold abatement process works
The process flexes to the condition, but these checkpoints keep decisions clear.
Inspection and moisture mapping
A certified technician walks the property with a moisture meter, thermal imaging camera, and boroscope. We map every wet zone, photograph visible growth, and take air samples with a spore trap sampler if you want lab confirmation. Most inspections take 45 to 90 minutes.
Written scope and price
You get a written scope the same day: what gets removed, what gets cleaned, how long it takes, and the total price. No hourly surprises. If the job is insurance-covered, we format the scope so your adjuster can process it without a back-and-forth.
Containment and removal
We seal the work area with poly and zipper doors, set up negative air with HEPA filtration, and suit up in full personal protective equipment. Contaminated drywall, insulation, and wood studs come out in sealed bags. Structural surfaces get HEPA vacuuming and dry ice blasting where the substrate can take it.
Treatment and drying
After removal, we apply an antimicrobial coating and, where specified, an encapsulation sealant. A fogger with Benefect or Concrobium reaches cavities a rag cannot. Dehumidifiers and air movers run until moisture readings match dry standard, usually 24 to 72 hours depending on the material.
Clearance testing and rebuild
We do not hand the keys back until a third-party or in-house clearance test passes. Spore counts come back at or below outdoor baseline, and you get the lab report. Then we schedule rebuild, or hand off to your contractor with photos and a written clearance.
Tools & methods
Tools and methods we use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Thermal imaging camera
Finds temperature differences that reveal hidden moisture behind walls, under floors, and in ceilings without opening anything up.
Boroscope inspection camera
Lets us see inside wall cavities, behind baseboards, and into attic corners where mold hides after slow leaks.
Moisture meter
Gives us calibrated readings on drywall, wood, and concrete so we know exactly when the structure has reached dry standard.
Negative air machine with HEPA filters
Keeps the containment under negative pressure so spores cannot escape into clean rooms during removal.
Air scrubber (Dri-Eaz, Phoenix Restoration Equipment)
Continuously filters airborne spores and particulates inside the containment zone, running for the full duration of the job.
Dry ice blasting machine
Removes mold from wood framing and block walls without water or abrasive media, leaving no secondary residue to clean up.
Spore trap sampler and air sampling media
Collects air samples before and after abatement so we can compare indoor spore counts to outdoor baseline.
Use cases
When to call for mold abatement
These examples show how the service framework adapts rather than forcing every call through one repair.

Bathroom mold behind shower tile
A Kirkwood homeowner had been bleaching grout lines for months. The mold kept coming back. Inspection with a boroscope found wet drywall and framing behind the shower wall, with visible growth across a 4-foot by 8-foot section. → We opened the wall, removed the contaminated drywall, HEPA vacuumed and treated the framing, and dried the cavity to dry standard in 48 hours. The exhaust fan was re-routed to vent outside. Clearance testing passed on the first sample.
Crawl space mold from ground moisture
A rental property near Downtown Bloomington had a persistent musty odor in the living room. Inspection found mold across the floor joists and subfloor, with relative humidity in the crawl space holding above 80 percent. → We removed contaminated insulation, HEPA vacuumed and treated the joists, and installed a 6-mil vapor barrier across the crawl space floor. Humidity dropped below 60 percent within a week. Clearance testing confirmed the space was clean.
Problems we solve
Mold problems we solve in Bloomington
Most mold calls in Bloomington trace back to one of a handful of moisture sources. Here are the ones we see most, what happens if you ignore them, and how we fix them.
Attic mold from swamp cooler leaks and bath fan discharge
We contain the attic, remove contaminated insulation, HEPA vacuum the framing, and treat the wood with an antimicrobial coating. Then we fix the source: re-route the bath fan or repair the cooler pan so it does not happen again. Most attic jobs finish in three to five days.
Crawl space mold from ground moisture and poor ventilation
We remove contaminated insulation, HEPA vacuum and treat the joists, and install a vapor barrier where it makes sense. If the crawl space needs encapsulation, we scope that separately so you can decide. Clearance testing confirms the space is clean before we close it up.
Bathroom mold behind tile and under caulk lines
We open the wall, remove the contaminated drywall, treat the framing, and dry the cavity to dry standard. Then we check the exhaust fan and confirm it is actually venting outside, not into the attic. Most bathroom jobs finish in one to two days.
Hidden mold after a slab leak or slow supply line drip
We use a thermal imaging camera and boroscope to find the wet zone, then open the wall and contain the area. Removal, treatment, and drying follow the same S520 process. We coordinate with your plumber so the source is fixed before we close anything up.
Pricing process
What mold abatement costs in Bloomington
$650 - $12,000 depending on scope
Square footage affected
The single biggest driver. A 20-square-foot bathroom is a different job than a 400-square-foot attic. We measure the actual contaminated area, not the whole room, so you do not pay for square footage that is clean.
Material type
Porous materials like drywall, insulation, and carpet have to come out. Non-porous surfaces like tile, block, and framing can usually be cleaned and treated, which costs less. We tell you which is which before we start.
Access and containment complexity
A crawl space with a 24-inch hatch takes longer to contain and work in than an open attic. Tight access adds labor hours, but it does not change the standard we follow.
How much does mold abatement cost in Bloomington CA?
Typical 2026 pricing in Bloomington runs $1,200 to $3,500 for a single affected room, and $4,000 to $12,000 for attic or crawl space jobs with wide contamination. Small bathroom mold removal can start closer to $650. Price depends on square footage, material type, and whether rebuild is included. We give you a written fixed price after the inspection, not a range.
What is the difference between mold abatement and remediation in Bloomington California?
In practice they are the same job. Abatement is the removal of mold and contaminated material; remediation is the full process of removal, cleaning, drying, and verification. Some contractors use abatement for the physical tear-out and remediation for the whole scope. When you hire us for mold abatement Bloomington CA, you get the full remediation process, including clearance testing.
How long does mold abatement take in Bloomington CA?
A single bathroom or closet usually takes one to two days of on-site work. Attic and crawl space jobs run three to five days. Add 24 to 72 hours of drying time if we are also correcting the moisture source. Clearance testing happens 24 hours after the final cleaning, and you get the lab report within one business day.
Who does mold mitigation near me in Bloomington?
We do. Our crews cover Bloomington, San Bernardino County, and the surrounding areas including Highland Village, Kirkwood, and Downtown Bloomington. Call (833) 929-5837 and we can usually be on-site the same day for an inspection. We are licensed, insured, and we follow the ANSI/IICRC S520 standard on every job.
Ready when you are
Get mold abatement Bloomington CA scheduled today
Mold spreads while you wait. Call (833) 929-5837 and we can usually be on-site the same day for an inspection and a written fixed price. Licensed, insured, and following the ANSI/IICRC S520 standard on every job in San Bernardino County.

Talk with the local team
Request Mold Abatement
Call (833) 929-5837 any time, day or night, and a live person will answer. We schedule free inspections seven days a week and can usually get to your BLOOMINGTON property the same day. If you prefer email, send photos of what you are seeing and we will follow up with next steps.



