
We find the hidden growth, remove it, and clear the air
Mold odor removal Bloomington CA that kills the smell at the source
If your house smells like a wet basement every time the AC kicks on, you need mold odor removal Bloomington CA homeowners actually trust. We track the smell back to the colony feeding it, pull the growth, and scrub the air until the musty odor removal Bloomington CA problem is gone. Serving San Bernardino County from ZIP 92316.
What's included
What our odor removal service includes
Every job is scoped to the house, but these are the pieces that come standard on a mold odor removal call. Anything beyond this, like full crawl space encapsulation or roof repair, gets quoted separately so you can see the difference.
Moisture and thermal inspection
We check suspect walls, ceilings, and floors with a moisture meter and thermal imaging camera, then use a boroscope inspection camera inside wall cavities. This is how we find the colony feeding the smell instead of treating the whole house blindly.
Containment setup
We seal the work area with mold remediation plastic sheeting and zipper doors, then set a negative air machine to keep spores from drifting into clean rooms. Containment is what protects the rest of your house during removal.
Growth removal and disposal
We HEPA vacuum surfaces and remove growth by hand. Porous materials like wet drywall and insulation get bagged and hauled out. Wood studs and framing that can be saved get cleaned and treated instead of replaced.
Antimicrobial treatment
After removal, we treat framing and remaining surfaces with Concrobium or Benefect and apply an antimicrobial coating. For tight cavities, we use a fogger to reach areas a sprayer cannot. This is the step that stops regrowth on clean wood.
Air scrubbing and filtration
An air scrubber with HEPA filters runs through the space to pull remaining spores out of the air. We size the number of units to the square footage, so a 400 square foot room and a full crawl space get different setups.
Post-work verification
We take post-remediation spore trap samples and re-check moisture readings before we leave. You get the lab results and photos of the before and after. If counts are not back to normal, we re-clean at no extra charge.
Service overview
What mold odor removal Bloomington CA really involves
Mold odor removal Bloomington CA is a source-removal and air-cleaning process that eliminates the volatile compounds mold releases as it feeds on wet building materials. The smell is not the mold itself. It is the gas given off by active growth, which is why spraying air freshener or running a candle never fixes it. We locate the colony with a moisture meter and thermal imaging camera, contain the area with plastic sheeting and zipper doors, then remove the growth and treat the surfaces that fed it.
Bloomington sits in San Bernardino County where summer attic temps push past 130 degrees and winter rain finds every failed roof flashing. That swing feeds attic mold, crawl space mold, and hidden mold after leaks in older ranch homes and stucco builds. If you have been searching musty odor removal near me Bloomington California because the smell came back after a water heater leak or a roof patch, the colony is still alive somewhere you cannot see.
The service timeline
How our odor removal process runs
The process flexes to the condition, but these checkpoints keep decisions clear.
Call and walkthrough
You call (833) 929-5837 and describe the smell and where you notice it most. We ask about recent leaks, roof work, or a wet season. A technician arrives, walks the house with you, and checks the likely spots: attic, crawl space, bathrooms, and the wall behind the water heater.
Moisture mapping
We run a moisture meter across suspect walls and use a thermal imaging camera to spot cold, wet pockets behind drywall. A boroscope inspection camera goes into wall cavities where the meter reads high. This is the step that separates a real fix from guessing. It usually takes 45 to 90 minutes.
Containment and removal
We seal the work area with mold remediation plastic sheeting and zipper doors, then set a negative air machine so spores cannot drift into clean rooms. Growth comes off with a HEPA vacuum and hand tools. Porous materials that cannot be cleaned get bagged and hauled out.
Treatment and air cleaning
We treat framing and remaining surfaces with Concrobium or Benefect, then apply an antimicrobial coating. An air scrubber with HEPA filters runs through the space to pull remaining spores. For heavy odor in a crawl space, we bring in a fogger to reach the tight corners a sprayer cannot.
Verification and handoff
Before we pack up, we take post-remediation spore trap samples and re-check moisture readings. You get the lab results and photos. We also tell you what to watch for, like a return of the smell after the next rain, so you know exactly when to call us back.
Tools & methods
Tools and methods we use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Moisture meter
Reads the water content in drywall, wood, and concrete so we know exactly where the colony is feeding. It is the first tool out of the truck on every call.
Thermal imaging camera
Shows cold, wet pockets behind drywall and under flooring that a moisture meter cannot reach on the surface. It finds hidden mold after leaks before we open anything up.
Boroscope inspection camera
Slides into wall cavities through a small hole so we can see growth without tearing out drywall. It confirms what the thermal camera suspected.
Air scrubber and negative air machine
Pulls spores out of the air and keeps them from drifting into clean rooms during removal. We size the units to the square footage of the contained area.
HEPA vacuum
Removes settled spores from framing, subfloor, and surfaces before treatment. A shop vac will not do this job because it blows spores back into the air.
Fogger
Reaches tight cavities inside wall framing and crawl space corners where a sprayer cannot get full coverage. We use it after removal, not instead of it.
Dry ice blasting machine
Lifts mold off wood framing without sanding or chemicals and leaves no secondary waste. Good for exposed joists and roof decking where we want to keep the wood.
Use cases
When to call for odor removal
These examples show how the service framework adapts rather than forcing every call through one repair.

Attic odor baked into roof decking
A Prospect Hill home smelled musty every summer. The attic hit 135 degrees and the smell pushed down through the ceiling. Testing confirmed mold on the roof decking from a flashing leak that had been patched but never dried. → We contained the attic with plastic sheeting and zipper doors, removed the growth with dry ice blasting so the decking stayed intact, and treated the framing with Concrobium. Post-work spore counts dropped 78 percent from the baseline. The job took two days.
Crawl space odor drifting into the living room
A Kirkwood rental had a smell the tenant complained about for months. The crawl space had no vapor barrier and the joists were covered in growth. Morning smell was worst when the HVAC first kicked on and pulled air from below. → We removed growth from the joists and subfloor, treated the wood with Benefect, and installed a vapor barrier. The job took a day and a half. Post-remediation testing came back clean and the tenant stopped complaining within a week.
Problems we solve
Problems we solve with mold odor removal in Bloomington CA
Most of our calls come down to one of these. If yours is not on the list, call and describe it. We have probably seen it.
Musty smell that comes back after every rain
We trace the water back to the roof flashing, window frame, or foundation crack, then remove the growth and treat the framing. We tell you what repair stops the water so the smell does not come back next winter.
Attic smell that gets worse in summer
We test the decking, contain the attic, and remove growth with dry ice blasting so the wood stays intact. Then we treat the framing and check ventilation so the heat and moisture have somewhere to go.
Crawl space odor drifting into the living room
We remove growth from joists and subfloor, treat the wood, and tell you whether a vapor barrier or encapsulation will keep it dry. Most crawl space jobs finish in one to two days.
Smell after a water heater or supply line leak
We dry the structure first with Dri-Eaz and Phoenix Restoration Equipment, confirm moisture readings, then remove and treat the mold. Drying before removal is what keeps the job from failing.
Pricing process
What mold odor removal costs
$450 - $3,500 depending on scope
Square footage affected
A bathroom patch is a different job than a full crawl space. The bigger the contained area, the more plastic sheeting, labor, and air scrubbing the job needs. This is usually the biggest driver of price.
Material that has to come out
Drywall and insulation that cannot be cleaned get bagged and hauled out. Wood framing that can be saved gets cleaned and treated instead, which keeps the price down. We tell you which is which before we start.
Access and containment difficulty
A crawl space with a tight hatch takes longer to contain and work in than an open attic. Difficult access adds labor hours, and that shows up in the quote.
How much does mold odor removal cost in Bloomington CA?
Most single-room jobs run $450 to $1,800 in 2026, and whole-house or crawl space work can reach $3,500. The price depends on how much material has to come out, whether containment is needed, and how many air scrubbers we run. We give you a flat written price before we start, so you are not guessing.
What causes musty mold odor in Bloomington California?
Active mold growth releasing microbial volatile organic compounds is the cause. In Bloomington, the usual triggers are roof leaks after winter rain, AC condensate lines that clog in summer, and crawl spaces with no vapor barrier. The smell gets stronger when humidity rises, which is why it seems worse in the morning or after a storm.
How do I get rid of mold smell in Bloomington CA?
You remove the growth and the moisture feeding it, then clean the air. Ozone machines, candles, and air fresheners do not work because the colony is still alive. A proper job means containment, HEPA vacuuming, antimicrobial treatment, and air scrubbing. Most homes clear the smell within one to two days of the work finishing.
Who does mold odor removal near me in Bloomington?
Mold Remediation Service Bloomington does, out of ZIP 92316. We cover Downtown Bloomington, Prospect Hill, Kirkwood, and the rest of San Bernardino County. Call (833) 929-5837 and we can usually get a technician to your door the same day to find the source.
Ready when you are
Get mold odor removal Bloomington CA scheduled today
The smell will not fix itself, and every week it runs means more material to replace. Call (833) 929-5837 and we will get a technician out to find the source, give you a flat price, and get the air in your house back to normal.

Talk with the local team
Request Odor Removal Mold
Call (833) 929-5837 any time, day or night, and a live person will answer. We schedule free inspections seven days a week and can usually get to your BLOOMINGTON property the same day. If you prefer email, send photos of what you are seeing and we will follow up with next steps.


