Residential Mold Testing

Air and surface sampling with lab results in 24 to 48 hours

Residential mold testing Bloomington CA you can trust

We handle residential mold testing Bloomington CA homeowners call about when a musty smell will not quit or a leak left a stain behind. Our technicians run moisture meter and thermal imaging sweeps, pull air and surface samples, and send them to an accredited lab. You get a written report with spore counts, photos, and a clear next step, usually within 24 to 48 hours.

Live phone supportUpfront optionsBacked workmanship
Call firstLive triage can help before arrival
Safety before speedRisks assessed before work begins
Diagnose the causeWe trace the source, not just the symptom
Approve the workScope and price explained upfront

What's included

What residential mold testing includes

Every testing visit covers the basics. Here is what you get as standard and what we can add on if the situation calls for it.

01

Visual inspection

We walk the attic, crawl space, bathrooms, kitchen, and any room with a musty odor. A boroscope inspection camera goes into wall cavities and behind baseboards where visible inspection cannot reach.

02

Moisture mapping

A calibrated moisture meter and thermal imaging camera read every suspect wall, ceiling, and floor. Readings above 16 percent on wood framing get flagged and photographed for the report.

03

Air sampling

We set spore trap cassettes for a 5 to 10 minute draw, plus one outdoor control sample. This gives you a comparison between indoor and outdoor spore counts, which is the number that matters.

04

Surface sampling

Visible growth gets swabbed or tape-lifted and sent to the lab for direct microscopy. This tells you the genus, which matters if you are worried about black mold growth or toxic mold exposure.

05

Written report

You get a report with photos, sample locations, lab results, and a plain-language summary. We email it and then call you to walk through what it means and what to do next.

06

Lab analysis

Samples ship to EMSL Analytical or Pro-Lab, both accredited for mold identification. Standard turnaround is 24 to 48 hours. Rush processing is available for an added fee.

Service overview

Residential mold testing Bloomington CA explained

Residential mold testing Bloomington CA is an inspection service that measures airborne spores and surface contamination inside a home to confirm whether mold is present, what type it is, and how far it has spread. We start with a moisture meter and thermal imaging camera to find wet building materials, then use a boroscope inspection camera inside walls and a spore trap sampler to capture air samples. Surface samples go to EMSL Analytical or Pro-Lab for direct microscopy.

Bloomington sits in San Bernardino County, where summer heat pushes indoor humidity up and winter rain finds every roof and window leak. Add the older stucco homes and slab-on-grade construction common around Downtown Bloomington, and you get hidden mold after leaks that never dries out. If you have been searching for home mold testing near me Bloomington California, we can be on site the same day and tell you exactly what is growing and where.

Know the mold typeLab analysis identifies the genus and rough spore count, so you know whether you are dealing with common Cladosporium or black mold growth that needs immediate attention. That distinction changes the scope, the cost, and how fast you need to act.
Find hidden moistureA thermal imaging camera and moisture meter read wall cavities, ceilings, and subfloor without cutting drywall. We regularly find wet wood studs behind bathroom tile and under kitchen sinks that the homeowner never suspected.
Document for insuranceOur written report includes photos, sample locations, and lab results you can hand to your adjuster. Claims move faster when the damage is documented before cleanup starts, not after.
Residential Mold Testing you can count on
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.

The service timeline

How our testing process works

The process flexes to the condition, but these checkpoints keep decisions clear.

01

Phone intake

We ask what you are seeing and smelling, when it started, and whether there was a leak or flood. That call takes about 10 minutes and lets us bring the right sampling media. Same-day and next-morning slots are usually open.

Stage 1
02

Visual walkthrough

On site, we inspect the attic, crawl space, bathrooms, and any room with a musty odor. A boroscope inspection camera goes into wall cavities and behind baseboards. This step runs 30 to 45 minutes on a typical 1,500 square foot home.

Stage 2
03

Moisture mapping

We run a moisture meter across suspect walls and use a thermal imaging camera to spot temperature differences that signal trapped water. Readings above 16 percent on wood framing get flagged and photographed for the report.

Stage 3
04

Air and surface sampling

We set spore trap cassettes for a 5 to 10 minute air draw, one outdoor control sample, and surface swabs on visible growth. Samples are sealed, labeled, and shipped to EMSL Analytical or Pro-Lab the same day.

Stage 4
05

Report and next steps

Results come back in 24 to 48 hours. We walk you through the spore counts, show you the photos, and tell you plainly whether you need remediation, a dehumidifier, or just a repair on the leak source.

Stage 5

Tools & methods

Tools and methods we use

Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.

01

Moisture meter

Reads moisture content in drywall, wood framing, and subfloor. Anything above 16 percent on wood gets flagged for further inspection.

02

Thermal imaging camera

Detects temperature differences that signal trapped moisture behind walls and ceilings without cutting into the surface.

03

Boroscope inspection camera

Goes into wall cavities, behind baseboards, and inside HVAC closets to find hidden mold growth.

04

Spore trap sampler

Draws a measured volume of air through a cassette that captures airborne spores for lab analysis.

05

Air scrubber

Filters airborne spores and particulates during remediation. We use HEPA filters rated for mold spore capture.

06

HEPA vacuum

Removes settled spores from surfaces and framing without spreading them into the air.

07

Dehumidifier

Pulls moisture out of the air in crawl spaces and attics to stop mold from returning after remediation.

Use cases

When to schedule mold testing

These examples show how the service framework adapts rather than forcing every call through one repair.

Residential Mold Testing
Attic mold after roof leakA homeowner in Green Acres noticed a musty smell in the hallway but could not find the source. The attic had visible black staining on the sheathing from a slow roof leak that had been going for months. → We sampled the sheathing and the attic air. Lab results confirmed elevated spores. We set up containment, removed the affected sheathing, treated the framing with Concrobium, and ran a HEPA vacuum. Post-remediation testing came back clean.

Crawl space mold from ground moisture

A rental property in Kirkwood had a persistent musty odor that tenants complained about. The crawl space had no vapor barrier and the joists were covered in white and black mold growth. → We tested the crawl space air and sampled the joists. Results showed elevated spore counts. We removed the growth, treated the wood with antimicrobial coating, and installed a vapor barrier. Clearance testing passed.

Bathroom mold behind tile

A homeowner in Downtown Bloomington saw black spots on the bathroom ceiling and grout. A moisture meter showed the wall behind the tile was wet from a slow supply line leak. → We swabbed the visible growth and sampled the air. Lab confirmed black mold growth. We removed the affected drywall and tile, treated the framing, and replaced the materials. Post-remediation testing passed.

Problems we solve

Problems we solve for Bloomington homeowners

Most calls start with a smell, a stain, or a leak that never quite dried out. Here is what we find and how we fix it.

ISSUE

Musty odor with no visible mold

We use a thermal imaging camera and moisture meter to find the wet spot, then sample the air in that room. If spores are elevated, we pinpoint the source and recommend targeted remediation instead of a whole-house job.

SYMPTOM

Black spots on bathroom walls or ceiling

We swab the visible growth for lab ID, check the moisture behind the tile, and confirm whether the growth is surface-level or has reached the framing. Then we remove it and treat the area with antimicrobial coating.

SIGN

Attic mold after a roof leak

We inspect the attic with a boroscope, sample the sheathing, and check the HVAC closet for contamination. If remediation is needed, we set up containment and use a HEPA vacuum and air scrubber to clean the space.

ALERT

Crawl space mold from ground moisture

We test the crawl space air and sample the joists. If mold is present, we remove it, treat the wood, and recommend a vapor barrier and dehumidifier to keep it from coming back.

Pricing process

What mold testing costs

$250 - $600 depending on scope

Phase 01

Number of samples

Each air or surface sample adds to the cost. A basic job uses two air samples. A thorough job with surface swabs and multiple rooms can use six or more.

Phase 02

Home size

Larger homes take longer to inspect and often need more samples to cover all the suspect areas. A 3,000 square foot home may need twice the samples of a 1,500 square foot home.

Phase 03

Crawl space or attic access

If the crawl space or attic is difficult to access, the inspection takes longer. We charge for the extra time, not a flat fee.

Questions before we arrive

Common questions about mold testing

Residential Mold Testing
Call (833) 929-5837
How much does residential mold testing cost in Bloomington CA?

Most residential jobs run $250 to $600 in 2026, depending on how many samples we pull. A basic air quality test with one outdoor control starts around $250. Adding surface swabs, a crawl space inspection, or a second HVAC sample pushes the total toward $600. You get the full price before we start.

How long do residential mold testing results take in Bloomington California?

Lab results come back in 24 to 48 hours for standard turnaround. If you need them faster, we can request rush processing through EMSL Analytical for an added fee, which typically delivers results in 12 to 24 hours. We email the report and call you to walk through the findings.

What does residential mold testing include in Bloomington CA?

Every inspection includes a visual walkthrough, moisture meter readings, thermal imaging, and at least one air sample with an outdoor control. Most jobs also include surface sampling on visible growth. You get a written report with photos, sample locations, spore counts, and a clear recommendation.

Where can I get residential mold testing near me in Bloomington?

We serve all of Bloomington and the surrounding San Bernardino County area, including the 92316 ZIP code. Call (833) 929-5837 and we can usually schedule same-day or next-morning service. We also cover nearby neighborhoods like Kirkwood, Elm Heights, and Sherwood Oaks.

Ready when you are

Schedule residential mold testing Bloomington CA today

If you smell something musty or see spots on the wall, get answers before it spreads. We are licensed, insured, and we use accredited labs. Call (833) 929-5837 and we can usually be on site the same day.

Residential Mold Testing

Talk with the local team

Request Residential Mold Testing

Call (833) 929-5837 any time, day or night, and a live person will answer. We schedule free inspections seven days a week and can usually get to your BLOOMINGTON property the same day. If you prefer email, send photos of what you are seeing and we will follow up with next steps.

18762 Valley Blvd, Bloomington, CA 92316, USA, BLOOMINGTON, CaliforniaMain office · technicians serve the full area

Thanks — your request is in. We will contact you shortly.

Call now